PANASONIC BB-HCE481A POE Zoom Network Camera
|
|
|
|
MANUFACTURER: PANASONIC
PRODUCT CODE: BB-HCE481A
|
|
See There When You Can't Be There
These cameras can be viewed and controlled from a standard Web browser, video display, or even a compatible cell phone or PDA(1). Place them in your home, office, vacation home or almost anywhere else that you'd like to keep an eye on things, with no PC required on location! They are easy to install and operate and require no additional software for the PC that you're viewing them on. Each camera also comes with a free Web address, which can track the camera automatically. All you need is a regular Web browser to view them on your PC, as all of the other required software, including control software (TCP/UDP) and e-mail software (SMTP), is already inside the camera.
Bring Any Image Right Up Close
Equipped with a 42x zoom function (a 21x optical zoom and a 2x digital zoom(2)), the camera lets you zoom in and out in a total of 12 steps (10-step optical zoom and 2-step digital zoom) to view objects that are close or far away.
Two-Way Voice Communication
An external microphone and amp-equipped speaker, both optional, enable two-way voice communication(3) (transceiver system) between the network camera and a PC used to monitor the camera image. In addition to conventional monitoring of images and sound, voice messages can be transmitted from the PC to the network camera. Voice transmission and reception can be switched easily from the PC used to monitor the image.
CCD Sensor for Enhanced Image Expression
This camera features a CCD (Charged Couple Device) for sharp, enhanced image expression. The image refreshing speed (maximum) has been increased to 30 images per second(4) for smoother displays of moving images.
Record Directly onto SD Cards
The BB-HCE481A features an SD Memory Card slot for recording images captured by the network camera directly onto an SD Memory Card (sold separately).
* Voices cannot be recorded.
Simple Ethernet Connection - No PC Required
Our cameras are attached through an Ethernet connection (or router) and power source, you don't need a computer at each location you want monitored. Each camera has a built-in Web server with IP address. To view the camera's images on a PC, simply open a graphics-capable Web browser and type in the cameras specified Internet address(password optional).
Control the Camera Remotely
Using a standard Web browser, video display, or even a compatible cell phone or PDA, you can control the movement of the camera. There is 350 of Pan (left & right) movement and 120 of Tilt (up & down) movement available. You can also assign a "Home Position" that allows you to return the camera to a pre-designated shooting position. Up to eight shooting positions can be registered in advance, so you can aim the camera exactly where you want it. You can also click on the part of the image you want to see, and automatically bring that part to the center of the screen.
Record Only What You Want to Record
The camera can be set to automatically record video at certain times and certain speeds. In addition, with optional, external sensors attached to the camera, it is possible for the camera to email(5) or record when triggered by motion, sound, light, timer, or even a push button. These convenient functions eliminate your need to constantly check the image.
Create Your Own Free Web Address
The FREE viewnetcam.com service allows you to create a personal Web address (e.g., http://bob.viewnetcam.com) at which your camera's live image can be found on the Internet. Access your Panasonic Network Camera live from virtually any Internet connection point around the world! Your Web browser is the only software you'll need. Here's how the camera and service works: special software embedded within your Panasonic Network Camera gives your camera the ability to locate your unique Internet address. No matter what kind of Internet connection you have or which Internet provider you use, the viewnetcam.com service will keep your camera's Internet address permanent.
Sensor Recording and Email Alerts
With the built-in heat sensor, the camera can be set to record and/or notify you by email when someone enters the room. It can even automatically move to a preset location when triggered, just in case someone was viewing a different part of the room.
1. Connecting the camera to the Internet requires Internet access and may require that you obtain additional hardware such as a cable or DSL modem, or a hub or router with a 10Base-T Ethernet connection. The camera will not be accessible from across the Internet unless the Internet connection is active. We cannot guarantee that your Internet connection will always be available. The frame rate of the motion image may be dependent upon the uplink speed of the Internet connection and other factors. Viewing may involve some time delay. Recommended minimum 100kbps upstream bandwidth for camera.
2. Digital zoom may significantly decrease resolution.
3. PLEASE NOTE that under certain circumstances, audio/video recording may be PROHIBITED by law. This device should be used only in compliance with all applicable federal, state and local statutes. This function can be used with a PC only. It cannot be used with a cell phone. To hear the voice transmitted from the PC, a commercially available speaker with a built-in amp must be installed. The transceiver system does not allow simultaneous transmission and reception of voices. A version upgrade may be required if you use under IPv6.
4. Image resolution: 320 x 240 or 160 x 120.
5. Email transmission may not be possible in some cases due to the mail server authentication system (SMTP authentication, etc.) used by your Internet service provider.
TECHNICAL SPECIFICATIONS:
SERVER FEATURES:
Image Compression: JPEG (Motion JPEG for moving image display)
Quality Video Resolution: 640 x 480, 320 x 240(default), 160 x 120 1
Image Quality: JPEG (favor clarity, standard, favor motion), MPEG4
Frame Rate: Max. 12 frames/sec. (640 x 480) Max. 30 frames/sec. (320 x 240, 160 x 120)
Authentication: User ID/password/IPSec
IPv4/v6: IPv4/v6 Dual Stack
Supported Network Protocols: IPv4 / IPv6 Dual Stack
IPv4: TCP, UDP, IP, HTTP, FTP, SMTP, DHCP, DNS, ARP, ICMP, POP3, NTP, IPsec, UPnP™,
IPv6: TCP, UDP, IP, HTTP, FTP, SMTP, DNS, ICMPv6, POP3, NDP, NTP, IPsec
Simultaneous Viewers Max. 30 simultaneous accesses (max. 10 accesses with voice reception)
Buffered Images Approx. 125 images (320 x 240)- standard image quality - with time display - without using SD Memory Card
Image Buffer Alarm, time or motion detection-Image Buffer Triggers
Image Transfer via E-Mail (SMTP) or FTP SMTP, FTP
Free DDNS Compatible (Viewnetcam.com) 2 Yes
Cellular Phone Compatibility View Snapshot and Control from Compatible Cell Phone
Multi-Language Interface Yes
CAMERA FEATURES:
Zoom: Max. 42x (21x Optical, 2x digital)
Image Sensor: 1/4" 380,000 pixel CCD
Viewing Angle: Horizontal-Tele: 2.6° (optical)/1.3° (digital), wide: 51°, Vertical-Tele: 1.9° (optical)/0.9° (digital), wide: 38°
Remote Pan Angle: -175° up to +175°
Remote Tilt Angle: -120° to 0° (on desk) 0° to 90 ° (on ceiling)
Maximum Pan/Tilt Speed: No
Lens Brightness: F1.6 (Wide), F3.6 (Tele)
Required Light Intensity: 3 to 100,000 lux (in Color Night View Mode: 0.09 to 100,000 lux)
Lens Focus Point: Auto/Manual (40 steps)
AUDIO FEATURES:
2-Way Audio: 2-Way half duplex
CODEC: ADPCM (32kbps)
Frequency Range: 300Hz - 3.4kHz
Input: External Microphone Input Terminal
Output: Audio Line Output Terminal for External Speaker
WIRELESS FEATURES:
Standard: No
Antenna: No
Wireless Technology: No
Frequency: No
Number of Channels: No
Transmission Speed: No
Security: No
INTERFACE FEATURES:
Network Connection: Ethernet (10Base-T/100Base-TX)
External I/O Connector: 2 input / 1 output
SD Card Slot for Image Buffer: Full Size (operation guaranteed for 2GB, 1GB, 512MB, 256MB, 128MB, and 64MB SD Memory Cards)
Speaker/Microphone Jack: 3.5mm mini-jack
OTHER FEATURES:
Built-in Sensor: Yes
Power Over Ethernet Compatibility: Yes
Operating Temperature: 0°C to +40°C (+32°F to +104°F)
Operating Humidity: 20-80% RHG, non-condensing
Power Source: PoE: 48V, IEEE 802.3af-compliant Power over Ethernet
AC adaptor: Input 120V AC
Output 12V DC (option)
Power Consumption PoE: 11W
Weight (only the unit): 650G (1.43 lb.)
Dimensions (H x W x D): 5 1/2" x 4 13/16" x 4 13/16"
|
 DOWNLOAD BB-HCE481A PRODUCT MANUAL
|
|
|
